EPOXY_MULTI POXY MORTAR_Three Component Epoxy Mortar Mix - MCCSA
10153
page-template-default,page,page-id-10153,page-child,parent-pageid-7810,ajax_fade,page_not_loaded,,qode-theme-ver-3.10,wpb-js-composer js-comp-ver-6.1,vc_responsive
 

MULTI POXY MORTAR 

THREE COMPONENT EPOXY MORTAR MIX 
 

DESCRIPTION

MULTI POXY MORTAR is an epoxy mortar mix that is used primarily to fill and raise horizontal surfaces or voids. Fine, hard aggregate makes the mortar high in strength and can be used on damp areas with good adhesion to concrete. Water washable and smooth finishing. Sets at low temperatures and is resistant to moisture and has excellent chemical resistance.   

 

TYPICAL APPLICATIONS

For use on commercial and industrial flooring and void filling applications where the mix can be compacted in. Long lasting, water resistant, chemical resistant mortar. Used on bridge decks, concrete structures, bearing pads and joint stops. 

 

ADVANTAGES

  • Hard wearing 
  • Long lasting 
  • Rapid hardening 
  • Smooth finishing 
  • Water washable 
  • Compacting mix application 
  • Concrete colour 
  • High resistance to water and chemicals 
  • Easy to maintain 
  • Non-cracking 
  • Abrasion and impact resistant 

 

TYPICAL PROPERTIES

Yield: 12.5L 

Coverage: 2m2 @ 6mm thick

Appearance: Grey Mortar

Application Temp: 10°C to 25 °C

Mortar Thickness: Unlimited

Pot Life: 20 minutes

Overcoat Time: 8-12 hours

Cure (Light Traffic): 12 hours

Full Cure: 7 Days

Compressive Strength: 70MPa

Bond Strength: 3,5 N/mm²

Cleaning: Water

 

WATCH POINTS

  • Exposure of the mortar to intense lighting or direct sunlight will produce discolouration in time. 
  • Do not hold a full kit in a bucket for long period of time while mixed, rather empty and spread out onto substrate within the working time of the product.  
  • Mortar maybe textured if resin is not worked to the surface by floating with a steel trowel. 

DIRECTIONS FOR USE

 

SURFACE PREPARATION

Surfaces to be clean, sound and free of deleterious substances. Remove all laitance, oil, grease, paints, mould oil or curing compound from surfaces using wire brush, bush hammer, scabbler or other plant as appropriate.  

 

PRIMING

Mix Part A (Resin) and Part B (Hardener) and roll or brush out over the substrate surface, working into the substrate where possible.

 

APPLICATION

Mix the resin and hardener together in a clean bucket and mix in the aggregate. Mix only enough to be able to spread and trowel out within the pot life of the epoxy. Trowel out into wet or tacky primer using trowels or straight edge over horizontal surfaces, and compact into place to remove trapped air. Steel trowel smooth and float for a smooth finish. If filling voids, prime the inside of the void and then compact in the epoxy mortar mix. Smooth off with a steel trowel. Allow 8-12 hours before overcoating or opening to light traffic. Overcoat with any solvent free epoxy-based coating such as MULTI POXY 1938 in colour of choice.

 

EQUIPMENT CARE

All tools should be cleaned with water immediately after use. If delayed, equipment will need thinners or mechanical action to clean or be discarded.

 

PACKAGING

Supplied in 2.45L Resin + 0.8L Hardener + 25kg Aggregate Kits

 

QUALITY ASSURANCE

Multi Construction Chemicals South Africa (PTY) Ltd production and testing programs comply with all local and international testing standards.

 

REVISION: 3.3

The information supplied is believed to be reliable. As we do not have any control over the processing or application of the product we cannot guarantee the results to be obtained.

Users assume all risks and liability resulting from the use of this product and must confirm suitability thereof by conducting their own tests.

No guarantee is expressed or implied. Liability to the replacement of faulty material.

FOR PROFESSIONAL USE ONLY.